Below is the process that we have specifically developed with our local Sherwin Williams for our painters to restore the interior of old wood windows WITHOUT removing the sash from the window. Yes, it would be best practice to remove them; however, to do so is sometimes cost prohibitive. This is a method that will perform the needed maintenance on the windows, be eligible for Sherwin William’s lifetime warranty, and allows our Neighbors (we don’t have customers) to do much needed work on more windows.
If you do want to remove it to bare wood and deglaze, we highly recommend using a Speedheater over a heat gun and check out this video.
(For our process in Spanish click here)
The following process is for our on-site, interior window restorations and part of our Lifetime Exterior Renovation. This is the difference between putting color on a window and prepping & painting a window that we can all stand behind the quality of work.
Any products outside of those specified and provided must be approved by Old Home Rescue prior to use.
Follow Manufacturer’s Specifications on all products
Clean the Surface
Remove all surface contamination by using the following;
Walls should be wet down with garden hose & nozzle
Mix 1 gallon water, 1 cup bleach, & 1 cup TSP-PF (Adjust for spray bottle if desired)
Working in sections, clean from bottom to top to avoid streaks
Rinse window and trim with water in spray bottle before solution dries
Allow to dry until wood as 15% or less moisture level
Prep the Surface
Cover the work area with plastic or drop clothes to collect paint debris
Scrape flat surfaces with a pull scraper to a sound layer removing existing loose, peeled or checked paint.
Scrape profiles with a surfaces with a profile scraper to a sound layer removing existing loose, peeled or checked paint.
Feather sand by hand any rough edges from peeling paint with a sanding pad to improve the final appearance and adhesion.
Removal of old paint runs
Set nail heads on wood where exposed beyond surface level
Remove all unused fasteners & hardware
Repair dry rot around around sash hardware with Abatron LiquidWood BEFORE priming.
Repair rot with up to a golf ball sized quantity of Abatron WoodEpox BEFORE priming. Damage or rot exceeding epoxy threshold should be communicated to Old Home Rescue
Repair minor cracks painter’s putty or wood filler AFTER spot priming.
Caulking should be completed AFTER priming
Glazing Repair
If broken glass is present, continue with steps 5.2-5.4.
Replace any broken glass with 1/8” double strength flat glass or reproduction wavy glass, as specified. Pin glass in place using glazing points with at least 2 glazing points on each side.
Glass beds should be primed with oil based primer BEFORE glazing.
Putty glaze glass in with AquaGlaze
Prime the Surface
Brush the surface with 1-2 coats of Sherwin Williams Primer Rx Peel Bonding Primer
Peel bonding primer helps even out less-than-perfect surfaces before painting, giving a smoother completed finish
Air, surface and material temperature must be above 35 degrees for 4 hrs after application
Caulk
Gaps and fixed joints can be filled with Sherwin Williams PowerHouse or MaxFlex caulking after priming the surface
Allow proper drying time before application of the finish
Paint the Surface
Brush the surfaces with 2 coats of Sherwin Williams Emerald, Waterbased Alkyd Urethane (different temperature requirements) or equivalent paints in a satin or semi gloss finish finish for ultimate protection.
OHR preferred sash brush: 2” angled ultra stiff sash brush
Air, surface and material temperature must be above 35 degrees for 48 hrs after application
Clean the surface
Remove any paint from glass with a lubricated razor blade
Clean glass with glass cleaner and paper towels
Glass should be clean when viewed from 6 feet away
Property should be clean of all construction debris and paint chips
Trash can be disposed of at Old Home Rescue or construction dumpster on-site.
Notes on Painting Wood Windows
The above specifications are for painting wood windows for stabilization, protection and maintenance on a cyclical basis. Window painting’s cosmetic results should be viewed from 5 feet away as there may still be inconsistencies in the paint surface.
If the Neighbor is interested in additional surface preparation or replacements parts to their window, direct them to the Old Home Rescue Project Manager, who will discuss off-site restoration or reproduction windows.